 |
 |
 |
|
The Red Lion PAXR0120 PAX series rate panel meter has a 5 digit, green LED display in a 1/8 DIN housing. The display offers 0.56" numbers. Compatible inputs can come from switch contacts, CMOS & TTL circuit outputs, magnetic pickups, and RLC sensors. It accommodates directional, uni-directional, & Quadrature signals. Four setpoint outputs can be supplied for the meter through an optional digital output plug in card. This panel meter proves ideal for use in industrial applications. The front panel has 5 keys, with 3 of them being programmable function keys. AC powered
Features
- 1/8 DIN Housing
- 5 Digit, Green LED Display
- Rate Indication
- Programmable Function Keys/User Inputs
- Four Setpoint Alarm Outputs (w/Option card)
- Min/Max Rate Displays w/Programmable Capture Time
- 85 to 250 VAC Input Power
- NEMA 4X/IP65 - Front Panel
- Adjustable Brightness Fits Surrounding Environment
- Parameters Can be Completely or Partially Locked After Setup
- Not made to directly command motors, valves or actuators without safeguards
Red Lion PAX Series User Manual
Specifications
Display
5 digit, 0.56" (14.2 mm) standard green LED
Annunciators:
r - rate, H - High Rate, L - Low Rate
SP1 - setpoint 1 output state, SP2 - setpoint 2 output state, SP3 - setpoint 3 output state, SP4 - setpoint 4 output state
Power Requirements
AC Power: 85 to 250 VAC, 50/60 Hz, 18 VA
Isolation: 2300 Vrms for 1 min. to all inputs and outputs. (300 V working)
Sensor Power
12 VDC, +/-10%, 100 mA max. Short circuit protected
Memory
Nonvolatile memory retains programmable parameters & display values
User Inputs
Three programmable user inputs
Max. Continuous Input: 30 VDC
Isolation To Sensor Input Commons: Not isolated
Logic State: Jumper selectable for sink/source logic
Response Time: 6 msec. typical; function dependent.
Rate Display
Accuracy: +/-0.01%
Minimum Frequency: 0.01 Hz
Maximum Frequency: 34 KHz
Maximum Display: 5 Digits: 99999
Adjustable Display (low) Update: 0.1 to 99.9 seconds
Input A
Logic: Input trigger levels VIL = 1.5 V max.; VIH = 3.75 V min.
Current sinking: Internal 7.8 KOhm pull-up to +12 VDC, IMAX = 1.9 mA.
Current sourcing: Internal 3.9 KOhm pull-down, 7.3 mA max. @ 28 VDC,
VMAX = 30 VDC.
MAGNETIC PICKUP: Sensitivity: 200 mV peak
Hysteresis: 100 mV
Input impedance: 3.9 KOhm @ 60 Hz
Maximum input voltage: +/-40 V peak, 30 Vrms
Output
Response Time: 25 microsec.; add 6 msec (typical) if a relay card is installed
Timed Output Accuracy: Rate = +/- 0.01% + 20 msec.
Standards Compliance
CE Approved
EN 61326-1 Immunity to Industrial Locations
Emission CISPR 11 Class A
EN 61010-1: General Requirements
EN 61010-2-030: Particular Requirements for Testing and Measuring Circuits
RoHS Compliant
UL Recognized Component: File #E179259
UL Listed: File #E137808
Type 4X Enclosure rating (Face only)
IP65 Enclosure rating (Face only)
IP20 Enclosure rating (Rear of unit)
Physical
Operating Temperature: 0 C to 50 C (32 F to 122 F)
Storage Temperature: -40 C to 60 C (-40 F to 140 F)
Humidity: 85% max. relative humidity (non-condensing)
Vibration to IEC 68-2-6: Operational 5 to 150 Hz, 2 g.
Shock to IEC 68-2-27: Operational 25 g (10 g relay).
Altitude: Up to 2000 meters
Construction: NEMA 4X/IP65 outdoor use, IP20 Touch Safe, Installation Category II,
Pollution Degree 2, One piece bezel/case; flame resistant; Synthetic rubber keypad; panel gasket & mounting clip
Connection: High Compression Cage-Clamp Terminal Block
Wire Strip Length: 0.3" (7.5 mm)
Wire Gage: 30-14 AWG copper wire
Torque: 4.5 inch-lbs (0.51 N-m) max.
Dimensions: 1.95" x 3.8" x 4.2"
|
|
|
 |
|
 |
|
