 |
 |
 |
|
The Red Lion PAXLCL00 PAX LCL Lite series current loop panel meter has a 3 1/2 digit, red LED display in a 1/8 DIN housing. This meter is used for the measurement of process variables. It covers almost any type of application that needs a readout for such indicators as pressure, flow, temperature, and level. It is designed for harsher conditions, including dirty surroundings and wash-down areas. AC powered
Features
- 1/8 DIN Housing
- 3 1/2 Digit, Red LED Display
- 24 VDC Excitation Display
- Dual range, 4 to 20mA or 10 to 50mA
- Wide Span & Offset Scaling Range
- Over Range Indication
- Selectable Decimal Points
- NEMA 4X/IP65 - Front Panel
Red Lion PAX LCL Lite Series User Manual
Specifications
Display
3-1/2 digit, 0.56" (14.2 mm) red LEDs
Power Requirements
AC Power: 85 to 250 VAC, 50/60 HZ, 6 VA
Isolation: 2300 Vrms for 1 min. between input and supply (300 V working voltage)
Input Sensitivity
260 units/mA @ 4 to 20 mA input
105 units/mA @ 10 to 50 mA input
Compliance
Voltage drop across input at max. signal current, less than
600 mV for both 4 to 20 and 10 to 50 mA ranges.
Input Resistance
4 to 20 mA - 29.2 Ohm
10 to 50 mA - 11.8 Ohm
Scaling Range
SPAN: 32 coarse steps (binary progression with 5 DIP switches) Each step
providing approx. 8.125 numerical units/mA/step sensitivity for 4 to 20
mA input and 3.25 units/mA/step for 10 to 50 mA input.
OFFSET: 16 coarse steps (binary progression with 4 DIP switches) with
+/- switch to add or subtract offset. Each step adds or subtracts approximately
175 from the numerical display for a total offset range of +/-2700.
Linearity: +/-(0.05% +/-1 digit)
Reading Rate:2.5 readings/sec
Response Time:1 sec to settle for step change
Excitation Supply: 24 VDC @ 50 mA max. Regulated and isolated.
Low Frequency Noise Rejection
Normal Mode Rejection: 63 dB @ 50/60 Hz
Common Mode Rejection: 100 dB, DC to 50/60 Hz
Standards Compliance
UL Recognized Component, File # E179259, UL61010A-1, CSA C22.2 No. 61010-1
UL Listed, File # E137808, UL508, CSA C22.2 No. 14-M95
Type 4X Enclosure rating (Face only), UL50
IECEE CB Scheme Test Report # 04ME11209-20041018
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment
for measurement, control, and laboratory use, Part 1.
IP65 Enclosure rating (Face only), IEC 529
IP20 Enclosure rating (Rear of unit), IEC 529
Electromagnetic Compatibility: See user manual
Physical
Operating Temperature: 0 C to 60 C (32 F to 140 F)
Storage Temperature: -40 C to 80 C (-40 F to 176 F)
Humidity: 85% max. relative humidity (non-condensing)
Span Temperature Coeff.: 100 PPM/°C
Offset Temperature Coeff.: 100 PPM/°C
Vibration to IEC 68-2-6: Operational 5 to 150 Hz, in X, Y, Z direction for 1.5 hours, 2 g's.
Shock to IEC 68-2-27: Operational 30 g, 11 msec in 3 directions
Altitude: Up to 2000 meters
Construction: NEMA 4X/IP65 outdoor use, IP20 Touch Safe, Installation Category II,
Pollution Degree 2, One piece bezel/case; flame resistant; panel gasket & mounting clip
Connection: High Compression Cage-Clamp Terminal Block
Wire Strip Length: 0.3" (7.5 mm)
Wire Gage: 30-14 AWG copper wire
Torque: 4.5 inch-lbs (0.51 N-m) max.
Dimensions: 1.95" x 3.8" x 4.2"
|
|
|
 |
|
 |
|
