 |
 |
 |
|
The Red Lion PAXI0020 PAX series
dual counter/rate panel meter has a 6 digit, Red LED display in a 1/8 DIN housing. The display offers 0.56" numbers. Compatible inputs can come from switch contacts, CMOS & TTL circuit outputs, magnetic pickups, and RLC sensors. Four setpoint outputs can be supplied for the meter through an optional digital output plug in card. It offers communications capability with separate option cards, including RS232, RS485, Modbus, DeviceNet, and Profibus DP. Another option card creates a linear DC output signal. AC powered
Features
- 1/8 DIN Housing
- 6 Digit, Red LED Display
- User Selectable Input Modes
- Rate Indication
- 5 Keys on Front Panel (3 Are Programmable Function Keys)
- Up to 3 Count Displays or a Serial Slave
- 10 Point Scaling for Non Linear Processes
- Four Setpoint Alarm Outputs (w/ Option card)
- Communications & Bus Capabilities (w/ Option card)
- Retransmitted Analog Output (w/Option card)
- Crimson Programming Software
- Ethernet (w/External Gateway)
- NEMA 4X/IP65 - Front Panel
- Accommodates Directional, Uni-Directional, & Quadrature Signals
- Red LEDs Readable in Sunlight
- Adjustable Brightness Intensity to Fit Surrounding Environment
- MAX & MIN Reading Memory w/Programmable Capture Time
- Parameters Can be Completely or Partially Locked After Setup
- Should not be used to directly command motors, valves, and actuators without safeguards
Red Lion PAX Series User Manual
Specifications
Display
6 digit, 0.56" (14.2 mm) red sunlight readable LED
Annunciators:
A, B, C, r - Rate, H - Max Rate, L - Min Rate, OF - Upper significant digit display of counter,
SP1 - setpoint 1 output state, SP2 - setpoint 2 output state, SP3 - setpoint 3 output state, SP4 - setpoint 4 output state
Power Requirements
AC Power: 85 to 250 VAC, 50/60 Hz, 18 VA
Isolation: 2300 Vrms for 1 min. to all inputs and outputs. (300 V working)
Sensor Power
12 VDC, +/-10%, 100 mA max. Short circuit protected
Memory
Nonvolatile memory retains programmable parameters & display values
User Inputs
Three programmable user inputs
Max. Continuous Input: 30 VDC
Isolation To Sensor Input Commons: Not isolated
Logic State: Jumper selectable for sink/source logic
Response Time: 6 msec. typical; function dependent.
Output
Response Time: 25 microsec.; add 6 msec (typical) if a relay card is installed
Timed Output Accuracy: Counter = +/- 0.01% + 10 msec. Rate = +/- 0.01% + 20 msec
Rate Display
Accuracy: +/-0.01%
Minimum Frequency: 0.01 Hz
Maximum Frequency: See User Manual
Maximum Display: 5 Digits: 99999
Adjustable Display (low) Update: 0.1 to 99.9 seconds
Counter Displays
Maximum display: 8 digits: +/- 99999999 (greater than 6 digits, the display
alternates between high order and low order.)
Prescaler Output
NPN Open Collector: ISNK = 100 mA max. @ VOL = 1 VDC max. VOH = 30
VDC max. With duty cycle of 25% min. and 50 % max
Standards Compliance
CE Approved
EN 61326-1 Immunity to Industrial Locations
Emission CISPR 11 Class A
EN 61010-1: General Requirements
EN 61010-2-030: Particular Requirements for Testing and Measuring Circuits
RoHS Compliant
UL Recognized Component: File #E179259
UL Listed: File #E137808
Type 4X Enclosure rating (Face only)
IP65 Enclosure rating (Face only)
IP20 Enclosure rating (Rear of unit)
Physical
Operating Temperature: 0 C to 50 C (32 F to 122 F)
Storage Temperature: -40 C to 60 C (-40 F to 140 F)
Humidity: 85% max. relative humidity (non-condensing)
Vibration to IEC 68-2-6: Operational 5 to 150 Hz, 2 g.
Shock to IEC 68-2-27: Operational 25 g (10 g relay).
Altitude: Up to 2000 meters
Construction: NEMA 4X/IP65 outdoor use, IP20 Touch Safe, Installation Category II,
Pollution Degree 2, One piece bezel/case; flame resistant; Synthetic rubber keypad; panel gasket & mounting clip
Connection: High Compression Cage-Clamp Terminal Block
Wire Strip Length: 0.3" (7.5 mm)
Wire Gage: 30-14 AWG copper wire
Torque: 4.5 inch-lbs (0.51 N-m) max.
Dimensions: 1.95" x 3.8" x 4.2"
|
|
|
 |
|
 |
|
