 |
 |
 |
|
The Red Lion PAXCK000 PAX series panel meter is a timer with real-time clock capability. It has a 6 digit, red LED display in a 1/8 DIN housing. It also features communication and bus capabilities through option cards, including RS232, RS485, Modbus, DeviceNet, and Profibus-DP. AC powered. Inputs can come from sources such as switch contacts or CMOS & TTL circuit outputs. There are 5 function keys on the front, with 3 being programmable to meet the needs of the application. Four setpoint outputs are possible through the use of an optional digital output card.
Features
- 1/8 DIN Housing
- 6 Digit, Red LED Display
- Elapsed Timer w/Preset Capability
- Real-Time Clock
- 4 Displays- Timer, Clock, Date, Counter
- Cycle Counting Capability
- Programmable Function Keys/User Inputs
- 4 Setpoint Alarm Outputs (w/Option card)
- Communication & Bus Capability (w/Option card)
- Crimson Programming Software
- NEMA 4X/IP65 - Front Panel
- After setup parameters can be partially or completely locked to avoid tampering
Red Lion PAX Series Timer User Manual
Specifications
Display
6 digit, 0.56" (14.2 mm) red sunlight readable LED
Annunciators:
TMR- Timer, CNT- Cycle Counter, DAT- Real time clock date or time
SP1 - setpoint 1 output state, SP2 - setpoint 2 output state, SP3 - setpoint 3 output state, SP4 - setpoint 4 output state
Power Requirements
AC Power: 85 to 250 VAC, 50/60 Hz, 18 VA
Isolation: 2300 Vrms for 1 min. to all inputs and outputs.
Sensor Power
12 VDC, +/-10%, 100 mA max. Short circuit protected
Memory
Nonvolatile E2PROM retains programmable parameters & display values
User Inputs
Three programmable user inputs
Logic inputs configurable as Current Sinking (active low) or Current
Sourcing (active high) through a single plug jumper.
Current Sinking (active low): VIL = 0.9 V max., 22 KOhm pull-up to +12 VDC.
Current Sourcing (active high): VIH = 3.6 V min., 22 KOhm pull-down, Max.
Continuous Input: 30 VDC.
Isolation To Timer Input Common: Not isolated
Response Time: 10 msec
Timer Display
Timer Range: 23 Selectable Ranges
Timing Accuracy: +/- 0.01%
Minimum Digit Resolution: 0.001 Sec.
Maximum Least Significant Digit Resolution: 1 Hr.
Maximum Display: 999999
Real Time Display
5 display formats
Hr/Min/Sec (12 or 24 Hr. format); Hr/Min (24 Hr.); Hr/Min (12 Hr. with
or without AM/PM indication)
Date Display: 7 display formats
Month/Day or Day/Month (numeric or 3-letter Month format); Month/
Day/Year or Day/Month/Year (all numeric);
Day of Week/Day (3-letter Day of Week format)
Cycle Counter Display
Counter Range: 0 to 999999
Digit Resolution: 1 cycle
Maximum Count Rate: 50 Hz
Timer Inputs A & B
Logic inputs configurable as Current Sinking (active low) or Current
Sourcing (active high) via a single plug jumper.
Current Sinking (active low): VIL = 0.9 V max., 22 KOhm pull-up to +12 VDC.
Current Sourcing (active high): VIH = 3.6 V min., 22 KOhm pull-down, Max.
Continuous Input: 30 VDC.
Timer Input Pulse Width: 1 msec min.
Timer Start/Stop Response Time: 1 msec max.
Filter: Software filtering provided for switch contact debounce. Filter
enabled or disabled through programming.
If enabled, filter results in 50 msec start/stop response time for successive
pulses on the same input terminal
Standards Compliance
CE Approved
EN 61326-1 Immunity to Industrial Locations
Emission CISPR 11 Class A
EN 61010-1: General Requirements
EN 61010-2-030: Particular Requirements for Testing and Measuring Circuits
RoHS Compliant
UL Recognized Component: File #E179259
UL Listed: File #E137808
Type 4X Enclosure rating (Face only)
IP65 Enclosure rating (Face only)
IP20 Enclosure rating (Rear of unit)
Physical
Operating Temperature: 0 C to 50 C (32 F to 122 F)
Storage Temperature: -40 C to 60 C (-40 F to 140 F)
Humidity: 85% max. relative humidity (non-condensing)
Vibration to IEC 68-2-6: Operational 5 to 150 Hz, 2 g.
Shock to IEC 68-2-27: Operational 25 g (10 g relay).
Altitude: Up to 2000 meters
Construction: NEMA 4X/IP65 outdoor use, IP20 Touch Safe, Installation Category II,
Pollution Degree 2, One piece bezel/case; flame resistant; Synthetic rubber keypad; panel gasket & mounting clip
Connection: High Compression Cage-Clamp Terminal Block
Wire Strip Length: 0.3" (7.5 mm)
Wire Gage: 30-14 AWG copper wire
Torque: 4.5 inch-lbs (0.51 N-m) max.
Dimensions: 1.95" x 3.8" x 4.2"
Besides the real time clock feature, this meter also works as an elapsed or preset timer, while also being able to show the date. There are two inputs with 23 timing ranges, with the ability to be a dual or quad output timer through the use of an option card. When used as a clock, the time can be shown in 12 or 24 hour formatting. Either format can indicate hours and minutes, or hours, minutes, and seconds. The 12 hour format has the option to show AM or PM. If displaying the date, it can show the month, day, and year. Leap years and time changes for Daylight Savings Time are automatically calibrated. When using multiple PAXCK units, they have the ability to sync up with each other, so all meters can indicate the same time throughout the workplace. This panel meter can be used as a clock and preset timer at the same time. The display indicates four different parameters, including the timer, count, date, and real time clock. The battery operated time clock card will continue to show the current time even without the use of main power.
|
|
|
 |
|
 |
|
